SolarAPP+, short for Solar Automated Permit Processing, is an online web portal that automates the plan review and process for issuing permits to qualified businesses or individuals to install code-compliant residential, roof-mounted photovoltaic (PV) systems. Based on model building, electrical, and fire codes, SolarAPP automatically performs a compliance check based on inputs supplied by the contractor to ensure the proposed system is safe and code compliant. Installation practices, workmanship, and adherence to the approved design are then verified through the inspection process.
If you are a licensed contractor or installer, you may register for a new SolarAPP+ account. (Non-licensed owner-builders must apply for a regular Building Permit with Plan Check.)
First provide basic contact information such as the name and address of your company. Then create a password that meets the security requirements (8 or more characters, 1 or more upper- and lower-case characters,1 or more numbers, 1 or more special characters and does not contain the user’s email or name). Additionally, you must select ‘Installer’ in the Account Type field. Our system will verify whether your provided address is valid. Please ensure that you read and accept the SolarAPP+ Terms of Use and Privacy Policy prior to registering for an account.
After you submit the registration form, you should see a pop-up screen that confirms your account registration. Before proceeding to submit project applications, you must provide the SolarAPP team your contractor license information, including numbers and expiration dates, for the each jurisdiction in you which you operate.
We will review the eligibility information and verify your contractor license in our system to complete the registration process. Once verified, you will be able to submit project applications in SolarAPP+ for addresses in enabled jurisdictions. Contact SolarAPP+ if you have difficulty registering for an account.
Projects must follow requirements outlined in the Eligibility Checklist to use SolarAPP+ for instant permitting. Listed below are the requirements that must be fulfilled in order to utilize the platform for automated project approval:
SolarAPP+ Photovoltaic Eligibility Checklist – September 7, 2021
System
New Rooftop Residential Retrofit Photovoltaic (PV) Systems
Installed by contractor with all licenses required by jurisdiction
Electrical
Limited to 2017 NEC
600V Max per DC System Size
Single phase only
No Aluminum Wires
Must Use 600V rated PV wire (due to outer diameter > 0.24" (6.1mm))
Must use 90 deg C rated insulated wire
Max 2 DC strings in parallel
Max 9 current carrying conductors in a raceway
Inverter output circuit conductors must be THWN-2, or listed NM
Terminals must be rated to 75 deg C, labeled for use with Cu wires, and accept minimum 8 AWG wire
If using microinverter, 1 module per microinverter
Permitted to install on up to or equal to 400A Service
Permitted to install on up to or equal to 225A Service Disconnect
Permitted to install on up to or equal to 225A busbars
No existing PV or ESS
May install only 1 module type
May install up to 2 Inverters for String Inverters, up to 1 inverter type for Micro-inverters and AC modules Systems
Conduit may not be Schedule 80 PVC
Single Family Dwelling Only
Modules and Inverters must be listed on CEC
Rapid Shutdown cannot be satisfied using the method: No exposed wiring or conductive parts [690.12(B)(2)(3)]
No trenching allowed
All power production inverter outputs have the same point of connection
All equipment is assumed to be non-continuous rated
May install only 1 racking system type
Height of rooftop conduit> =7/8 inch
Flat Plate PV Modules Only
Structural
Applicable International Residential Code
PV system + hardware weight is less than or equal to 4 pounds per square foot
No ground mounted systems
No carports or non-permanent structures
No wood shake or wood shingle roofing
Limit of 10 inches above the roof for pitched (>2/12) roof systems
No metal roof or low-slope roof in areas with>15 pounds per square foot snow load
Installers will pay a small administration fee to use SolarAPP+. In turn, contractors will receive instant permits online for compliant applications, saving installers a significant amount of time and effort on every permit processed.
Administrative fees will be used to cover ongoing maintenance, customer support, technical assistance, and software development as the product moves to self-sustained commercialization and away from direct support from the Department of Energy (DOE).
After issuance, projects can be revised as many times as the contractor wishes prior to installation. After revisions are complete and the project is submitted, SolarAPP+ will then run another compliance check. If your updated system design is code compliant, the system will reissue your updated permit and alert Permit Sonoma with a revised Approval Document and Inspection Checklist.
The first three revisions are free of charge, while each subsequent revision would charge the installer a fee. If a revision requires payment of an additional fee, the revised permit is not issued until the fee is paid.
Below are frequently asked questions (FAQs) related to SolarAPP+.
Translate